分中棒又叫尋邊器，是在CNC數控加工中，用于精確確定被加工工件的中心位置的一種檢測工具、分中棒的工作原理是首先在X軸上選定一邊為零、再選另一邊得出數值，取其一半為X軸中點，然后按同樣方法找出Y軸原點，這樣工件在XY平面的加工中心就得到了確定。因為生產的需要分中棒有不同的類型，如光電式、防磁式、回轉式、陶瓷式、偏置式等，比較常用的是偏置式。偏置式分中棒、光電式分中棒特點、不需要回轉測量、精確度可以達到、±0.005mm   陶瓷分中棒、偏置式分中棒特點、Φ10的直柄可以安裝在切削夾頭或鉆孔夾頭上、用手指輕壓測定子的側邊、使其偏心0.5mm、3.使其以400-600RPM的速度轉動、彈簧力力較小、可以避免小銑刀或小鉆頭斷裂、使測定子的與加工件的端面相接觸，一點一點的觸碰移動，就會達到全接觸狀態，測定子即不會震動，宛如靜止的狀態接觸著，如果此時加以外力，測定子就會偏移出位，此處滑動的起點就是所要求的基準位置、.加工件本身的端面位置，就是加上測定子半徑5mm的坐標位置、偏置式分中棒使用注意事項：  偏置式分中棒使用范例、勿使用分中棒彎曲或勉強拖拉，否則會影響精度、.滑動端面勿粘附異物或微塵、在測量時、轉速不能超過600RPM、偏置式分中棒不適合在橫型的機器上使用、分中棒詳細規格及價格表、專業生產 陶瓷分中棒 陶瓷尋邊器 閃光鳳鳴尋邊器 質量優價格低 適合經銷商拿貨。
專業生產 陶瓷分中棒 陶瓷尋邊器 閃光鳳鳴尋邊器 質量優價格低 適合經銷商拿貨。

     Points in the bar called edge finder is used to accurately determine the center of a workpiece to be machined in CNC machining, inspection tools, points in the rod works is first selected in the X-axis side of zero.re-election to the other side come to value, whichever is half of the X-axis midpoint, and then the same method to find the Y-axis origin, so that the processing center of the workpiece in the XY plane to determine. Used because the rods have the need of production of different types, such as photoelectric, magnetically shielded type, rotary, ceramic type, bias type, bias type. Offset points in the rod, the rod characteristics of the photoelectric points, no rotation measurement, the accuracy can reach ± 0.005mm in the points of the ceramic rods, offset points in the bar features, Φ10 shank can be installed in the cutting chuck or drill chuck hole Gently press the determination of sub-side with your fingers, so eccentric 0.5mm 3. it to the 400-600 RPM speed of rotation, the small force of the spring force can be avoided small cutter or a small drill bit breakage, so that determination of the child in contact with the workpiece end face, a little bit of touch mobile, will reach the Keys, the determination of the child that will not shock, like a stationary state in contact with at this time to be external, partial determination of the child will out of position, sliding the starting point here is the required reference position, the processing of their own end location is coupled with determination of the coordinates of the location of the ionic radius 5mm offset points in the rod Note: using the example of offset points in the rod Do not use points in the rod bending or barely drag, otherwise it will affect the accuracy. Do not slide the end adhesion of foreign matter or dust in the measurements, the speed can not exceed 600 RPM offset points in the rod is not suitable for use in cross-machine points in the rod detailed specifications and price list, specializing in the production of ceramic points in stick ceramic edge finder flash the Fengming edge finder quality excellent low prices for dealers getting goods.